asphalt standard according to astm

asphalt standard according to astm

SUPERPAVE ASPHALT CONCRETE END PRODUCT SPECIFICATION

SUPERPAVE ASPHALT CONCRETE END PRODUCT SPECIFICATION (EPS) NOVEMBER 2017 4 • ASTM D3665, Standard Practice for Random Sampling of Construction Materials • ASTM D4791, Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Part

Learn More

Indirect Tensile Test for the Determination of the Stiffness

Modulus of bituminous mixes determined by the Indirect Tensile Test, conducted according to the EN 12697-26, Annex C and the ASTM D 4123 standards. The testing was performed on high-performance bituminous mixtures, including polymer modified base-binder a

Learn More

ASTM International - ASTM D6307-05(2010) - Standard Test

Standard Test Method for Asphalt Content of Hot-Mix Asphalt by Ignition Method 1.1 This test method covers the determination of asphalt content of hot-mix asphalt ... ASTM D545-99 - Standard Test Methods for Preformed Expansion Joint Fillers for Concrete

Learn More

ASPHALT PAVEMENT TEXTURING SPECIFICATION PART 1 – GENERAL

ASPHALT PAVEMENT TEXTURING SPECIFICATION 1 March 2009 March 2009 PART 1 – GENERAL 1.1 DESCRIPTION A. Asphalt pavement texturing is a highly suitable solution for a wide variety of decorative pavement applications. Paved entranceways, parking lots, residen

Learn More

Dynamic Shear Rheometers SmartPave for Asphalt

For standard asphalt tests according to AASHTO, ASTM, DIN EN, and FGSV Temperature range: -30 °C to 120 °C Upgradeable to all standard rheological tests With the modular compact rheometer MCR 502S rounding off the portfolio, Anton Paar rheometers meet all

Learn More

Determination of Optimum Emulsified Asphalt Content of Cold

7.1. Mix specimens at the target optimum emulsified asphalt content established. Mix according to ASTM D7196 for lab blended mixtures. 7.2. Cure the specimens for 4 hours at 50°F and 50% relative humidity. 7.3. Abrade the specimens for 15 minutes accordin

Learn More

MATERIAL SPECIFICATION FOR AGGREGATES - HOT MIX ASPHALT

This specification covers material requirements for aggregates for use in hot mix asphalt (HMA). 1003.02 REFERENCES . This specification refers to the following standards, specifications, or publications: Ontario Provincial Standard Specifications, Constr

Learn More

Tests Applied on Bitumen | Procedure of Tests on Asphalt

Ductility Test on Asphalt . The ductility test (ASTM D113) measures the distance a standard asphalt sample will stretch without breaking under a standard testing condition (5 cm/min at 25 °C). It is generally considered that an asphalt with a very low duc

Learn More

Asphalt Emulsion CSS-1h

Asphalt Emulsion CSS-1h components are carefully selected and balanced, according to formulations developed by ExxonMobil. The quality of ExxonMobil products is assured for every delivery. They are produced and controlled according to the ExxonMobil Produ

Learn More

Shingle specification - National Roofing Contractors

an ASTM International test method in 2005. The current edition is ASTM D7158-11. According to ASTM D7158, asphalt shingles are classified as Class D if they pass at a basic wind speed of 90 mph, Class G if they pass at a basic wind speed of 120 mph or Cla

Learn More

Paving Asphalt 60/70 N

Paving Asphalt 60/70 N is a penetration graded asphalt product derived from specially selected crude oils via carefully controlled refining processes. The quality …

Learn More

ASTM D3381/D3381M - Standard Specification for Viscosity

For asphalt binders graded by penetration at 25 °C [77 °F], see Specification D946/D946M. If needed, volume corrections for asphalt binders should be made according to Practice D4311/ D4311M. The values stated in either SI units or inch-pound units are to

Learn More

ASTM D3381/D3381M-18

Dec 15, 2018 · For asphalt binders graded by penetration at 25 °C [77 °F], see Specification D946/D946M. If needed, volume corrections for asphalt binders should be made according to Practice D4311/D4311M . 1.2 The values stated in either SI units or inc

Learn More

ASTM D5361/D5361M - 16 - Standard Practice for Sampling

Purchase your copy of ASTM D5361/D5361M - 16 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available online in electronic and print formats. ASTM D5361/D5361M - 16 - Standard Practice for Sampling Compacted

Learn More

Playground Surfacing Standards - Playground Professionals

ASTM F1292 is the core standard of the subcommittee and has been updated over the years to include a field test, an instrumented free-fall test device, and the use of a hemispherical headform that replaces the ANSI C headform. The subcommittee on playgrou

Learn More

Standard Specification for Asphalt-Rubber Binder’

Standard Specification for Asphalt-Rubber Binder’ d Now-The value f‚or specific gravity in I_.3 I was corrected and additional editorial update> were made throughout in October I wis. 1. Scope 1.1 This specification covers asphalt-rubber binder, consist-i

Learn More

ASPHALT CONCRETE PAVEMENT PART 1 GENERAL

ASPHALT CONCRETE PAVEMENT PART 2 PRODUCTS 2.01 ASPHALT CEMENT 2.02 PRIME COAT 2.03 TACK COAT 2.04 AGGREGATES Asphalt cement used in the manufacture of each class of Asphalt Concrete Pavement shall be 150 - 200 (A) Grade conforming to the requirements of A

Learn More

Standard Specification for Viscosity-Graded Asphalt Cement

The purchaser shall specify the applicable table of limits. In the event the purchaser does not specify limits, Table 1 shall apply. For asphalt cements graded by penetration at 77°F (25°C) (see Specification D 946). If needed, volume corrections for asph

Learn More

SECTION 321216 - ASPHALT PAVING

A. Hot-Mix Asphalt Paving Terminology: Refer to ASTM D 8 for definitions of terms. B. DOT: Department of Transportation. 1.3 SYSTEM DESCRIPTION A. Provide hot-mix asphalt patching according to materials, workmanship, and other applicable requirements of s

Learn More

DESIGN GUIDELINES AND TECHNICAL STANDARDS

ii. Prime Coat: ASTM D 2027, medium-curing cutback asphalt matching IDOT MC-30 per Section 1032 of the Standard Specifications for Road and Bridge construction. iii. Tack Coat: IDOT SS-1, SS-1hP, CSS-1, CSS-1hP, emulsified asphalt or cationic emulsified a

Learn More

Leave a comment